Skoda Octavia Workshop Edition 08.1996 Manual Electrical System S00.5117.50.20

Skoda Octavia Workshop (S00.5117.50.20 Edition 08.96) Manual Electrical System PDF

CONTENTS:

Starter, Power supply

  • Battery
  • – Battery handling instructions
  • – Inspecting electrolyte level
  • – Measuring voltage under load
  • – Testing electrolyte density
  • – Charging battery
  • – Quick charger/starting aid
  • – Removing and installing battery
  • – Battery with magic eye
  • – Topping up electrolyte level
  • Removing and installing generator
  • – Vehicles with petrol engine
  • – Vehicles with diesel engine
  • – Removing and installing belt pulley of AC generator
  • Removing and installing starter

Gauges, Instruments

  • Dash panel insert ( > MY 00)
  • – Self-diagnosis
  • – Initiating self-diagnosis of the dash panel insert
  • – Interrogating fault memory
  • – Fault table
  • – Actuator diagnosis
  • – Erasing fault memory
  • – Ending output
  • – Coding control unit
  • – Reading measured value block
  • – Adaptation
  • – Adapting service interval display
  • – Input values when replacing the dash panel insert
  • – Resetting SID after service without V.A.G 1552/1551
  • – Resetting SID after service with V.A.G 1552/1551
  • – Removing and installing dash panel insert
  • – Bulb assignment on the dash panel insert
  • – Contact assignment of plug connections on the dash panel insert
  • – Testing signal of fuel gauge sender -G-
  • – Contact assignment at fuel gauge sender -G-
  • – Testing coolant temperature sender
  • – Testing speed signal
  • Taximeter and Printer
  • – Removing and installing taximeter HALE
  • – Removing and installing printer HALE
  • Dash panel insert (MY 01 >)
  • – Self-diagnosis
  • – Initiating self-diagnosis of the dash panel insert
  • – Interrogating fault memory
  • – Fault table
  • – Actuator diagnosis
  • – Erasing fault memory
  • – Ending output
  • – Coding dash panel insert
  • – Reading measured value block
  • – Adaptation
  • – Adapting service interval data when replacing the dash panel insert
  • – Input values when replacing the dash panel insert
  • Self-diagnosis of the Gateway
  • – Initiating self-diagnosis
  • – Interrogating fault memory
  • – Fault table
  • – Erasing fault memory
  • – Ending output
  • – Coding control unit
  • – Reading measured value block
  • – Removing and installing dash panel insert
  • – Contact assignment of plug connections on the dash panel insert
  • – Testing signal of fuel gauge sender -G-
  • – Testing contact assignment of fuel gauge sender -G-
  • – Testing coolant temperature sender
  • – Testing speed signal
  • – Testing output temperature sender -G17-
  • – Testing oil level/oil temperature sender -G266-
  • CAN databus
  • – Testing CAN databus drive
  • – Testing terminating resistances of the control units
  • – Testing CAN databus for short circuit
  • – Testing CAN databus convenience

Radio, Two-Way Radio, Mobile Phone

  • Radio systems
  • – General notes
  • – Radio system with 4 loudspeakers
  • – Radio system with 8 loudspeakers
  • – Overview of radio systems
  • – Removing and installing radio
  • – Removing and installing loudspeaker
  • – Removing and installing radio “Gamma (MS 501), MS 303, Symphony”
  • Removing and installing roof antenna
  • Telephone systems
  • – Overview of telephone systems
  • – Telephone preinstallation 1
  • – Telephone preinstallation 2 – Cullmann
  • – Telephone system
  • Removing and installing telephone operating electronics control unit -J412-(interface box)
  • Overview of holder for mobile phone 1
  • Overview of holder for mobile phone 2
  • Removing and installing telephone microphone -R38- > 08.00
  • Removing and installing telephone microphone -R38- 09.00 >
  • Self-diagnosis of radio system “Gamma (MS 501), MS 303 and Symphony”
  • – Connect vehicle system tester V.A.G 1552 and select radio control unit
  • – Interrogating and erasing fault memory
  • – Fault table
  • – Actuator diagnosis
  • – Coding radio
  • – Reading measured value block
  • Removing and installing CD changer
  • Radio-Navigation system (RNS)
  • – General description.
  • – Self-diagnosis of radio unit in RNS
  • – Self-diagnosis of navigation unit in RNS
  • – Interrogating and erasing fault memory
  • – Fault table
  • – Actuator diagnosis
  • – Reading measured value block
  • – Adaptation
  • – Coding RNS control unit
  • – Electronic anti-theft lock
  • – Plug connections at Radio-Navigation System
  • – Removing and installing Radio-Navigation System
  • Multi-function steering wheel
  • – General description
  • – Interrogating and erasing fault memory
  • – Fault table
  • – Coding multi-function steering wheel control unit -J453-
  • – Actuator diagnosis
  • – Reading measured value block
  • – Removing and installing pressure unit for multi-function steering wheel
  • – Contact assignment of 18-pin connector for multi-function steering wheel CU -J453-

Windscreen wiper and washer system

  • Windscreen wiper system
  • – Removing and installing windscreen wiper system
  • – Setting park position of windscreen wiper blades
  • Servicing windscreen washer system
  • – Removing and installing windshield washer fluid reservoir
  • – Removing and installing spray nozzles
  • – Adjusting spray nozzles
  • Servicing headlamp cleaning system
  • – Removing and installing spray nozzles of headlamp cleaning system
  • – Adjusting spray nozzles
  • – Removing and installing windshield washer fluid reservoir
  • Rear window wiper and washer system
  • – Rear window wiper system – Summary of components
  • – Removing and installing rear window wiper
  • – Setting park position of rear window wiper
  • – Adjusting spray nozzle
  • – Replacing spray nozzle (Octavia Estate)
  • – Replacing spray nozzle (Octavia)
  • – Removing and installing wiper rubber
  • – Removing and installing rain sensor

Exterior Lights, Bulbs and Switches

  • Servicing headlights
  • – Overview >- 07.00
  • – Overview 08.00 >-
  • – Removing and installing headlights
  • – Setting headlights
  • – Replacing bulbs at headlights
  • – Removing and installing headlight range control motor
  • Servicing turn signal lights
  • – Removing and installing turn signal lights
  • – Removing and installing bulb for turn signal light
  • – Removing and installing side turn signal lights
  • Servicing rear lights
  • – Overview
  • – Removing and installing bulbs from lamp holder
  • – Removing and installing rear light
  • Removing and installing licence plate illumination
  • Servicing steering column switch
  • – Removing and installing steering column switch
  • – Contact assignment at steering column switch – until MY 98
  • – Contact assignment at steering column switch – as of MY 99
  • Servicing lock cylinder and ignition starter switch
  • – Removing and installing lock cylinder
  • – Removing and installing ignition starter switch
  • – Contact assignment at ignition starter switch
  • Removing and installing rear lights of Octavia Estate
  • Additional brake light
  • – Additional brake light for Octavia
  • – Additional brake light for Octavia Estate
  • Anti-theft alarm system
  • – Contact switch for anti-theft alarm system F120 (engine hood)
  • – Horn for anti-theft alarm system H8
  • – Alarm system with its own power supply H12
  • – Replacing emergency battery for alarm system
  • Overview of parking aid
  • – Removing and installing parking aid control unit -J446-
  • – Removing and installing parking aid warning buzzer -H15-
  • – Removing and installing parking aid sender
  • Self-diagnosis of parking aid (parking system)
  • – General notes
  • – Initiating self-diagnosis of parking aid
  • – Interrogating and erasing fault memory
  • – Fault table
  • – Coding control unit
  • – Reading measured value block
  • – Adaptation
  • Roof sign „TAXI“
  • – Removing and installing bracket of roof sign „Taxi“
  • Self-diagnosis for xenon headlight with automatic regulation (system Litronic 4.1)
  • – Interrogating fault memory
  • – Fault table
  • – Actuator diagnosis
  • – Initiating basic setting
  • – Erasing fault memory
  • – Ending output
  • – Coding control unit
  • – Reading measured value block
  • Xenon headlight with automatic regulation (system Litronic 4.1) -overview
  • – Headlight with control unit
  • – Removing and installing front xenon headlight
  • – Replacing bulbs in headlights
  • – Removing and installing discharge lamp D2S
  • – Removing and installing ignition/high voltage unit BOSCH 2.3
  • – Removing and installing step motor
  • – Removing and installing front sender
  • – Removing and installing rear sender
  • – Removing and installing control unit
  • – Sender adjusting options
  • – Contact assignment of Xenon headlights
  • – Switch-over of the headlight inner aperture
  • – Ungluing a halogen headlight

Interior Lights, Bulbs and Switches – Anti-theft lock

  • Diagnosis of electronic immobiliser
  • – Self-diagnosis of 1st generation immobiliser
  • – Initiating self-diagnosis of immobiliser
  • – Interrogating control unit version
  • – Interrogating fault memory
  • – Fault table for the immobiliser
  • – Erasing fault memory
  • – Ending output
  • – Reading measured value block
  • – Adaptation
  • – Adaptation of car key
  • – Procedure in case the key is lost
  • – Adaptation after replacing the engine control unit
  • – Adaptation after replacing the immobiliser control unit
  • – Emergency start function with V.A.G 1552
  • – Emergency start function without V.A.G 1552
  • – Defective transponder and/ or key is lost
  • – Replacing reading coil
  • – Procedure when replacing the lock set or the immobilizer control unit
  • – System test
  • Servicing switches
  • – Removing and installing switches in centre console
  • – Removing and installing light switch
  • – Removing and installing adjuster for headlamp range control
  • – Removing and installing door contact switch
  • – Removing and installing switch for sun roof and interior light
  • – Removing and installing mirror adjustment switch
  • – Removing and installing window lifter switch
  • Servicing interior lights
  • – Removing and installing glove box light
  • – Removing and installing rear reading lights
  • – Removing and installing ashtray illumination
  • – Removing and installing make-up mirror lamp
  • – Removing and installing door warning lamp
  • – Removing and installing warning lamp for deactivated airbag
  • Servicing horn
  • – Removing and installing horn
  • Removing and installing luggage compartment lights
  • Removing and installing switch for remote release/fuel tank lid
  • Removing and installing luggage compartment power socket

Language: English
Format: PDF
Pages: 308

Skoda Octavia Workshop Edition 08.1996 Manual Electrical System S00.5117.50.20

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More