Seat Automatic gearbox 09G – 6-speed Workshop Manual

Ibiza 2016- Ibiza ST 2016- Leon 2013- Leon ST 2013-. Edition 11.2016. Technical information should always be available to the foremen and mechanics, because their careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a matter of course, be observed.

List of Workshop Manual Repair Groups

Repair Group
00 – Technical data
32 – Torque converter
37 – Controls, housing
38 – Gears, control
39 – Final drive – rear differential

CONTENTS

  • 00 – Technical data
    • 1 Safety instructions
      • 1.1 General safety regulations
      • 1.2 Safety precautions during road tests in which testing and measuring equipment is used
      • 1.3 Notes on tow-starting and towing
    • 2 Identification
      • 2.1 Gearbox codes
      • 2.2 Identifying the torque converter
    • 3 Repair notes
      • 3.1 General notes
      • 3.2 Cleaning rules
      • 3.3 General repair notes
      • 3.4 Gaskets, seals
      • 3.5 Bolts, nuts
    • 4 Technical data
      • 4.1 Allocation gearbox – engine
      • 4.2 Filling quantity
    • 5 Electrical components
      • 5.1 Fitting location overview – electrical components
    • 1.1 Exploded view – torque converter
      • 1.2 Torque converter: emptying
      • 1.3 Removing and installing oil seal for torque converter
      • 1.4 Removing and installing torque converter
      • 1.5 Torque converter: check
  • 37 – Controls, housing
    • 1 ATF circuit
      • 1.1 Assembly overview – ATF circuit
      • 1.2 ATF radiator: removing and installing
    • 2 ATF
      • 2.1 check the ATF level
      • 2.2 Changing the ATF
    • 3 Gearbox: removing and fitting
      • 3.1 Removing gearbox
      • 3.2 Installing gearbox
      • 3.3 Specified torques for gearbox
    • 4 Transport of gearbox
    • 5 Installing to engine and gearbox support
    • 6 Selector mechanism
      • 6.1 Exploded view – selector mechanism
      • 6.2 Emergency release from position P
      • 6.3 Removing and installing selector lever handle
      • 6.4 Moving button to installation position in the handle
      • 6.5 Gear selection mechanism: removing and fitting
      • 6.6 Selector lever control cable: removing and fitting
      • 6.7 Gear mechanism: verification
      • 6.8 Selector lever control cable: checking and adjusting
      • 6.9 Removing and installing multi-function switch
      • 6.10 Adjust the Multi-function switch
      • 6.11 Seal for the selector shaft: replacement
  • 38 – Gears, control
    • 1 ATF system
      • 1.1 Removing and replacing oil sump
      • 1.2 Removing and installing ATF strainer
    • 2 Valve body
      • 2.1 Assembly overview – valve body
      • 2.2 Valve body: Removal and installation
      • 2.3 Wire routing, connectors, connections and retainer on valve body
      • 2.4 Wiring harness for solenoid valves and senders: Removal and installation . .
      • 2.5 Gearbox input speed sender G182 : removing and fitting
      • 2.6 Gearbox output speed sender G195 : removing and fitting
  • 39 – Final drive – rear differential
    • 1 Sealing rings
      • 1.1 Renewing left oil seal
      • 1.2 Renewing right oil seal
    • 2 Gearbox control
      • 2.1 Removing and installing gearbox control unit

Language: English
Format: PDF
Pages: 96

Seat Automatic gearbox 09G – 6-speed Workshop Manual

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More