Nissan MR18 Engine Manual

CONTENTS

  • PRECAUTIONS
  • Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT BELT PRE-TEN-SIONER”
  • Precautionsfor ProcedureswithoutCow l TopCover.
  • PrecautionsNecessaryforSteeringWheelRotation After Battery Disconnect
  • OPERATION PROCEDURE
  • Precautions for Drain Coolant
  • Precautions for Disconnecting Fuel Piping
  • Precautions for Removal and Disassembly
  • Precautions for Inspection, Repair and Replacement
  • Precautions for Assembly and Installation
  • Parts Requiring Angular Tightening
  • Precautions for Liquid Gasket
  • REMOVAL OF LIQUID GASKET SEALING
  • LIQUID GASKET APPLICATION PROCEDURE
  • PREPARATION
  • Special Service Tools
  • Commercial Service Tools
  • NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
  • NVH Troubleshooting — Engine Noise
  • Use the Chart Below to Help You Find the Cause of the Symptom
  • DRIVE BELTS
  • Components
  • Checking Drive Belts
  • Tension Adjustment
  • Removal and Installation
  • REMOVAL
  • INSTALLATION
  • Removal and Installation of Drive Belt Auto-Tensioner
  • REMOVAL
  • INSTALLATION
  • AIR CLEANER AND AIR DUCT
  • Components
  • Removal and Installation
  • REMOVAL
  • INSTALLATION
  • Changing Air Cleaner Filter
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • INTAKE MANIFOLD
  • Components
  • Removal and Installation
  • REMOVAL
  • INSTALLATION
  • INSPECTION AFTER INSTALLATION
  • EXHAUST MANIFOLD
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • OIL PAN
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • IGNITION COIL, SPARK PLUG AND ROCKER COVER
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • FUEL INJECTOR AND FUEL TUBE
  • Components
  • Removal and Installation
  • REMOVAL
  • INSTALLATION
  • TIMING CHAIN
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • CAMSHAFT
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • INSPECTION AFTER INSTALLATION
  • Valve Clearance
  • INSPECTION
  • ADJUSTMENT
  • OIL SEAL
  • Removal and Installation of Valve Oil Seal
  • REMOVAL
  • INSTALLATION
  • Removal and Installation of Front Oil Seal
  • REMOVAL
  • INSTALLATION
  • Removal and Installation of Rear Oil Seal
  • REMOVAL
  • INSTALLATION
  • CYLINDER HEAD
  • On-Vehicle Service
  • CHECKING COMPRESSION PRESSURE
  • Components
  • Removal and Installation
  • REMOVAL
  • INSPECTION AFTER REMOVAL
  • INSTALLATION
  • Components
  • Disassembly and Assembly
  • DISASSEMBLY
  • ASSEMBLY
  • Inspection After Disassembly
  • VALVE DIMENSIONS
  • VALVE GUIDE CLEARANCE
  • VALVE GUIDE REPLACEMENT
  • VALVE SEAT CONTACT
  • VALVE SEAT REPLACEMENT
  • VALVE SPRING SQUARENESS
  • VALVE SPRING DIMENSIONS AND VALVE
  • SPRING PRESSURE LOAD
  • ENGINE ASSEMBLY
  • Components
  • Removal and Installation
  • REMOVAL
  • INSTALLATION
  • INSPECTION AFTER INSTALLATION
  • CYLINDER BLOCK
  • Components
  • Disassembly and Assembly
  • DISASSEMBLY
  • ASSEMBLY
  • How to Select Piston and Bearing
  • DESCRIPTION
  • HOW TO SELECT PISTON
  • HOW TO SELECT CONNECTING ROD BEARING
  • HOW TO SELECT MAIN BEARING
  • Inspection After Disassembly
  • CRANKSHAFT END PLAY
  • CONNECTING ROD SIDE CLEARANCE
  • PISTON TO PISTON PIN OIL CLEARANCE
  • PISTON RING SIDE CLEARANCE
  • PISTON RING END GAP
  • CONNECTING ROD BEND AND TORSION
  • CONNECTING ROD BIG END DIAMETER
  • CONNECTING ROD BUSHING OIL CLEARANCE
  • CYLINDER BLOCK TOP SURFACE DISTORTION
  • MAIN BEARING HOUSING INNER DIAMETER
  • PISTON TO CYLINDER BORE CLEARANCE
  • CRANKSHAFT MAIN JOURNAL DIAMETER
  • CRANKSHAFT PIN JOURNAL DIAMETER
  • OUT-OF-ROUND AND TAPER OF CRANK-SHAFT
  • CRANKSHAFT RUNOUT
  • CONNECTING ROD BEARING OIL CLEARANCE
  • MAIN BEARING OIL CLEARANCE
  • MAIN BEARING CRUSH HEIGHT
  • CONNECTING ROD BEARING CRUSH
  • HEIGHT
  • MAIN BEARING CAP BOLT OUTER DIAMETER. 103 CONNECTING ROD BOLT OUTER DIAMETER
  • CLOGGED OR DAMAGED OIL FILTER (FOR INTAKE VALVE TIMING CONTROL)
  • FLYWHEEL DEFLECTION (M/T MODELS)
  • MOVEMENT AMOUNT OF FLYWHEEL (M/T MODELS)
  • SERVICE DATA AND SPECIFICATIONS (SDS)
  • Standard and Limit
  • GENERAL SPECIFICATIONS
  • DRIVE BELT
  • WATER CONTROL VALVE
  • EXHAUST MANIFOLD
  • THERMOSTAT
  • SPARK PLUG
  • CYLINDER HEAD
  • VALVE
  • CAMSHAFT AND CAMSHAFT BEARING
  • CYLINDER BLOCK
  • PISTON, PISTON RING AND PISTON PIN
  • CONNECTING ROD
  • CRANKSHAFT
  • MAIN BEARING
  • CONNECTING ROD BEARING

Language: English
Format: PDF
Pages: 116

Nissan MR18 Engine Manual

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More