Claas Jaguar Fault Codes list

Table of CIS System Fault Codes

Code	Module	Fault	Working State	Eliminating
And-1	Device CAB	The oil pressure in the engine is too low
E-2	Device CAB	The oil level in the engine is too low
E-3	Device CAB	Water Pump Defective	The charging control lights up and does not charge.	Check the drive of the water pump and the generator. Check the charging control on the generator (61).
E-4	Device CAB	Cooling water temperature too high
E-5	Device CAB	The hydraulic temperature of the chassis is too high
E-6	Device CAB	Tightened Manual Brake
E-8	Electro-hydraulic drive of chassis EFA	Erroneous power supply voltage of the potentiometer
E-11	Device CAB	The hydraulic pressure of the chassis or the oil level is too low
E-12	Device CAB	Temperature Charge Air too high
E-13	ESR	Metal Detector Defective
E-14	ESR	Metal Detector, Interrupt
E-15	Device CAB	Reserve CAB
E-16	ESR	Still Connected Adapter box SFM Note SFM = self-propelled mower)		If necessary, check the configuration (SFH Or SFM).

Code	Module	Fault	Working State	Eliminating
E-17	ESR	The sensor of the speed of the feeding device is defective		Check the plug connection on the sensor and cable connections.
E-18	ESR	The sensor of the speed of the feeding device is defective		Check the plug connection on the sensor and cable connections.
E-19	Device CAB	The hydraulic motor of the chassis drive does not match the configuration of the
E-20	Electrohydraulic drive of chassis EFA	New module EFA = > It is necessary to study the potentiometer of the movement lever	This message appears after you install a new module EFA When the ignition is turned on. After examining the potentiometers of the movement lever and hydraulic flows, this message no longer appears.	1. Study Spinner Lever Movement 2. Study of Hydraulic flows Through the system CDS The hydraulic oil must Have a working temperature. Pressure sensor voltage values must be < 1.2 v.
E-25	ESR	Malfunction on the flow of the hydraulic pump of the feeding device
E-27	Electrohydraulic drive of chassis EFA	Valve exit defect PWM Trailer Brakes
E-30	ESR	The quick stop valve is constantly energized
E-32	Device CAB	Module CAN-Bridge Defective		Check the power supply of the module. Check the landing strength and pin pins.

Code	Module	Fault	Working State	Eliminating
E-33	ESR	Module ESR Defective		Check Power supply Module. Check the landing strength and pin pins.
E-34	Autopath Cac	Module Contour System Defective		Check Power supply Module. Check the landing strength and pin pins.
E-36	GGS	Defect Module GGS		Check Power supply Module. Check the landing strength and pin pins.
E-37	Electro-hydraulic drive of chassis EFA	Module EFA Defective	Emergency STOP: This indicates a defect in the module’s power output during operation. should be disconnected. Driving is no longer possible.	Turn off the machine and run again, if the malfunction no longer appears, the module is still in order, в Otherwise replace the module.
E-38	KSR	Module Management Damper Defective
E-39	ATP	Reserve, Autopilot
E-40	Electro-hydraulic drive of chassis EFA	Defective Valve Hydraulic	Emergency mode: The machine moves only the rear Progress With Speed Ok. 2 km/hour on the 2nd gear and 1 km/h on the 1st transfer. When the short-circuit is identified, the valve is stopped and the movement is no longer possible.	Flap That’s impossible Manage: Check the cable connection to the valve. Check the module output. Measure coil resistance, range of values: 6-12 Ohm Check the plug connection on the valve.

Code	Module	Fault	Working State	Eliminating
E-41	Electro-hydraulic drive of chassis EFA	Malfunctioning solenoid valve of hydraulic motor	Limited Operation: Movement to Max. 7 km/hour on the 1st transfer, Approx. 12 km/h on 2nd gear	Flap That’s impossible Manage: Check the cable connection of the module To Short circuit or breakage. Check Output Module.
				Measure coil resistance, range of values: 6-12 Ohm
				Check the plug connection on the valve.
E-42	Electrohydraulic drive of chassis EFA	3-nd magnet of the electromagnetic valve is defective	Emergency STOP: The machine moves by inertia to the stop, further movement is not possible.	Flap That’s impossible Manage: Check the cable connection of the module To Short circuit or breakage. Check Output Module.
				Measure coil resistance, range of values: 6-12 Ohm
				Check the plug connection on the valve.

Code	Module	Fault	Working State	Eliminating
E-43	Electro-hydraulic drive of chassis EFA	Defect of the electromagnetic valve of the hydraulic pump for the movement back	Emergency mode: The machine moves only forward at a speed Ok. 2 km/hour on the 2nd gear and 1 km/hour on the 1st transfer When the short-circuit is identified, the valve has an emergency stop, the movement of more That’s impossible.	Flap That’s impossible Manage: Check the cable connection of the module To Short circuit or breakage. Check Output Module.
				Measure coil resistance, range of values: 6-12 Ohm
				Check the plug connection on the valve.
E-44	Device CAB	The engine’s communications system is out of order	Missing bus CAN To Module ADM. Module It’s working Incorrectly.	Check the power supply of the modules. Check the cable trunk to the modules (conclusions).
E-45	GGS	Grinding Stone not in the original position
E-46	Electro-hydraulic drive of chassis EFA	Defective Potentiometer Lever Movement	Emergency mode: The machine moves at a speed of 1 km/hour only in the direction of forward. (Movement direction recognition by means of neutral position switch and reversing switch)	The potentiometer of the movement lever is made in the form of a double potentiometer. The fault signal is issued in the following cases: Incorrect polarity of the potentiometers of movement, breakage of a cable set, defective contact strip of a potentiometer.
				Eliminating:
				Check the voltage of the potentiometer of movement, check the plug connection on the potentiometer.

Code

Module

Fault

Working State

Eliminating

E-46

Check the cable set of the module to the potentiometer on the breakage or short circuit.

The potentiometer of Motion 2 produces the opposite signal, the sum of which with the signal of the potentiometer of motion 1 should always have constant value.

If the total signal does not lie within the range of 7.3-7.5 B, the potentiometer of the movement lever is defective.

Example:

Signal 1 = 4.0 in

Signal 2 = 3.4 in = >

Amount: 4.0 + 3.4 = 7.4

in = > potentiometer is OK.

Signal 2 = 1.0 in = >

Amount: 4.0 + 1.0 = 5.0

in = > Potentiometer defective

Measure Potentiometer.

Code	Module	Fault	Working State	Eliminating
E-47	Electro-hydraulic drive of running Part EFA	Lever potentiometer tolerance exceeded	Unusual behavior when driving. The final speed is not reached.	The potentiometer of the movement lever is made in the form of double Spinner:
			Despite the return of the lever of movement back speed reduction is not performed at first (Slow Reaction).	Valid Values Spinner Movement 1:
			Speedstar Fur: Only code delivery, Behavior Movement Not Changes.	Neutral Position: 3.8- 4.2 In Forward: 6.9-7.3 in
				Back: 0.8-1.2 in
				If there is an excess of values forward or backward on the mechanical end positions of the movement lever, it is necessary to align the control system of the movement lever potentiometer.
				The potentiometer of Motion 2 produces the opposite signal, the sum of which with the signal of the potentiometer of motion 1 should always have constant value.
				If the total signal does not lie within the specified range, the potentiometer of the movement lever is defective.
				Speedstar Fur: Check the angle sensor and the traction system, BT 31A POS 50, 10, 47

Code	Module	Fault	Working State	Eliminating
E-48	ESR	Metal In the Flow Device	The feeding device stands, the metal detector has worked.	Remove the metal. is not a malfunction in the sense of the word.
E-49	ESR	Stop slipping clutch of Coupling Consoles	Console Disables.	Message without Overload: Check the cable set to the console and from it. Check the speed sensor of the console.
E-50	ESR	Adapter box not recognized SFM	Module ESR Recognize speed sensors Disk 8500, but there are no 5 in the adapter box.	Plug Connection: Check the 13-pole plug on the driver’s site (corrosion). Breakage or short-circuit of the signal wire to the module ESR.
E-51	Device CAB	The cooling water level is too low		Refuel Cooling Water. The cable kit or plug causes a short circuit to be Mass.
E-52	ESR	No speed recognition of the feeding device	A fault message can be issued with multiple reversal without cause. When feeding, the feeder is disconnected after the fault message is issued.	Check the plug connection on the speed sensor. Check the 13-pole plug on the driver’s site (corrosion). Breakage or short-circuit of the signal wire to the module ESR. When installing the console Kemper Module must be installed ESR 014 213.4 (500 Ms.).

Code	Module	Fault	Working State	Eliminating
E-53	ESR	Short Circuit of the external key switch reversing	When the main drive is switched on, the machine reverses simultaneously.	Check the reversal key switch on the drawer near the wheel (short circuit).
				Check the key switch in the Multifunkcionaln Handle (short circuit).

Code	Module	Fault	Working State	Eliminating
E-54	Electro-hydraulic drive of chassis EFA	Interruption of study due to exceeding the time limit or incorrect starting condition	Normal operation: The error signal is given only when examining the potentiometer of the movement lever.	1st opportunity: When starting the study there were incorrect conditions:
				The movement lever is not in a neutral position.
				The lever of motion in the study was initially given back.
				The potentiometer of movement at the start of the study is outside the tolerance zone.
				2nd Possibility:
				During 15 seconds do not recognized the change of the signal of the potentiometer of motion, this study is interrupted.
				At the same time the code e-180 is issued, because acceptable values of the potentiometer are not achieved.
				If there are no errors concerning the driving drive before memorizing the signal, you can continue to operate the machine on the previous parameter values.
				But if the study was conducted on the basis of the surfaced previously reported failure, then the study should be repeated until it is successfully completed, otherwise the machine can only work in emergency mode.

Code	Module	Fault	Working State	Eliminating
E-55	Device CAB	There is no signal of traffic switch on roads
E-56	ESR	The speed sensor of the left Mowing The machine reports a stop
E-57	ESR	Medium speed Sensor Mowing The machine reports a stop
E-58	ESR	The speed sensor of the right Mowing The machine reports a stop
E-59	ESR	Switch Reducer Not Switches		Check the switch on the reversing gearbox.
E-60	Device CAB	Switch Transfer Not Was
E-63	CIS	Failure Module ESR
E-64	CIS	Failure Module Cac
E-65	CIS	Failure Module Fem	Module for 8700 is similar to the module ESR.	Again Configure Car. Remove the yield measuring device.
E-66	CIS	Failure Module GGS
E-68	CIS	Failure Module KSR
E-69	CIS	Failure Module ATP
E-70	Device CAB	Maintenance interval is over 10 hours
E-71	Device CAB	Maintenance interval is over 50 hours
E-72	Device CAB	Maintenance interval is over 100 hours
E-73	Device CAB	Maintenance interval is over 500 hours
E-74	ESR	Defect of the speed sensor of the console

Code	Module	Fault	Working State	Eliminating
E-75	JelektrogidRavlicheskij Drive of the chassis EFA	Brake pressure relay maintenance period exceeded	Normal operation: The driver gets the requirement to use the work force within 20 hours Brake.	After the machine is restarted, the braking pressure relay must be checked.
			If it does not pay attention to the fault message, the switch to emergency mode is made.	To do this, move the lever slightly out of the neutral position. To do this, press the brake pedal with force when the diesel engine is running until a 3-fold beep is issued, indicating a successful test.
				If the scan is finished without success, the Lever Movement is switched to the emergency Mode.
				Then run the validation again.
				If during the interval the brake pedal is pressed with such force that the test criteria are met, the interval automatically rises to 20 hours.

Code	Module	Fault	Working State	Eliminating
E-76	Electro-hydraulic drive of chassis EFA	The study of the flow of hydraulic motors failed	Through the system CDS The hydraulic flow is re-examined. This is necessary, for example, when replacing a module EFA or hydraulic unit, at strong fluctuations of the final speed 38-42 km/h) or if the final speed is not reached (for example, Max. 35 km/hour by car at speed of 40 km/h). The machine is in normal mode.	In case of unsuccessful study the first completely Turn off the machine and then run the diesel engine again. Be sure to follow the system CDS. Do the study again. If the malfunction remains or signaled other malfunctions, first process them.
				The following currents should be considered in the study:
				Studied Currents, 1280 ma indicate malfunction of the hydraulic unit turning system.
				With the same hydraulic units (no replacement of the hydraulic unit) The current difference > 50 ma between the old and new current value indicates a malfunction of the corresponding block.
				The hydraulic oil must have a working temperature.

Code	Module	Fault	Working State	Eliminating
E-77	Electro-hydraulic drive of chassis EFA	The range of the neutral position of the movement lever switch is exceeded	Emergency mode: The machine moves at a speed of 1 km/hour only in the direction of forward. (Movement direction recognition by means of neutral position switch and reversing switch)	The voltage value of the potentiometer of movement to the moment of switching of the neutral position switch differs from the value of the voltage stored at the last process of studying the potentiometer of motion.
				It is possible that there have been changes in the traction potentiometer system of the chassis.
				This malfunction can be eliminated by examining the potentiometer of the movement.
				Check the traction system of the movement lever potentiometer and the behavior of the neutral position switch.
E-78	ESR	Worked Coupling Walterscheid	Coupling Worked Due Overload.	Check the latch, distance, spring, etc.
E-80	GGS	Reserve GGS
E-81	Electro-hydraulic drive of chassis EFA Way Part EFA	Module EFA does not recognize engine speed	The diesel engine switches to the emergency Mode,> 800 rpm.	Check speed sensor DC On the jaw shaft and on the engine exit.
E-82	Device CAB	The distance between the longer rolls does not change
E-83	GGS	No friction resistance (gearbox malfunction or Spindle

Code	Module	Fault	Working State	Eliminating
E-84	Device CAB	Potentiometer of the movement lever outside the permitted tolerance
E-88	Device CAB	Defect of inductive motion speed sensor
E-89	ATP	Sensor Rotation Defective
E-95	Device CAB	Switch Not It’s possible
E-96	Device CAB	Filling Fuel Grandma < 10 %		Fill
E-98	Device CAB	Chuck Air Filter Scored
E-99	Device CAB	Reduced engine speed is activated
E-100	Device CAB	No movement lever potentiometer signal
E-101	Device	Minimum		Code ExtinguishedTo
	CAB	Voltage Battery < 10		Example, After
		В		Lifting Speed
				Rotation (Like
				Control Charging).
E-102	Device CAB	Overexertion Battery > 16 in		The cable connection on the generator has weakened.
				Gradual deterioration, fault reports become more frequent.
				Check Disconnect Battery.
				Battery Or Cell Defective.
E-103	Electro-hydraulic drive of chassis EFA	Not Included Transfer
E-104	Electro-hydraulic drive of chassis EFA Way Part EFA	Position Cabin Not Acceptable

Code	Module	Fault	Working State	Eliminating
E-105	ATP	Laser Scanner Defective
E-106	Autopath Cac	The pressure sensor of the contour system is defective
E-107	Autopath Cac	Sensor Pressure Accumulator Defective
E-108	Autopath Cac	Copier Right Faulty
E-109	Autopath Cac	Copier Left Faulty
E-110	Autopath Cac	Potentiometer Height Consoles Faulty
E-111	ATP	Wheel angle Sensor defective
E-112	ATP	Carbon copy System Right Faulty
E-113	ATP	Carbon copy System Left Faulty
E-114	KSR	potentiometer height of unloading pipe faulty
E-115	KSR	Potentiometer Damper Faulty
E-117	KSR	Laser Sensor Faulty
E-118	Device CAB	Drive on all wheels, despite riding on Road, 20 km/h, still active
E-119	KSR	Potentiometer position of unloading pipe faulty
E-123	GGS	Too loud knock on The Cutting Plate
E-124	GGS	The wrong state of the main drive, the speed of engine rotation is not in order
E-126	Autopath Cac	Missing Reaction Hydraulics
E-130	ATP	Reserve, Autopilot
E-131	ATP	Reserve, Autopilot

Code	Module	Fault	Working State	Eliminating
E-132	GGS	No pulses from the engine on the right
E-133	GGS	There are no pulses from the engine on the left
E-134	GGS	The mass line is defective to the knock sensor (left or right)
E-149	Device CAB	Air conditioning Defective
E-150	GGS	No impact on the final switch of the grinding stone
E-151	ESR	The end switch of the reverse is still active
E-153	ESR	The speed of the hydraulic engine of the feeding device has been exceeded
E-154	ESR	Metal detector Not Erased
E-155	ATP	Switch Seat Not Closed
E-155	ESR	Switch Seat Not Closed
E-156	ESR	To turn off the feeding device with the seat switch
E-157	ESR	Disabling the feeder due to overheating or short-circuiting of the unit

Code	Module	Fault	Working State	Eliminating
E-161	Electro-hydraulic drive of chassis EFA	There is no signal of the neutral position of the movement lever	Emergency mode: The fault message is issued if the machine is immediately launched on the module EFA There is no 12-in signal from the neutral position of the movement lever. For this purpose the movement lever should be in a neutral position (otherwise it is impossible to start the machine due to blocking of start). The machine can be moved only by reversing at a speed of 2 km/h. Code indication E 161 stops About Through 2 – 3 Seconds.	Check the cable connection of the module with the plug of the neutral position of the movement lever on the breakage. Check the signal of the neutral position switch (Micro directly on the potentiometer). Check the position of the control roller relative to the segment (center of Cut). The deformation of the reed is possible. Neutral Position = 3.9-4.0 in on the display. The preferred position of the movement lever, attributed to 3.90 B, is the rear turn in the neutral backstage.
E-162	KDS	No signal flow meter, water tank is empty
E-162	KDS	Tank Wolf Empty
E-163	KDS	Error Dosage Wolf
E-164	GGS	Specify: Sure Adjust GGS !
E-166	GGS	Knock Not Stop
E-167	ESR	Disabling the feeder due to overheating or increased current of the unit ESR

Code	Module	Fault	Working State	Eliminating
E-168	Device CAB	Wrong signal of traffic switch on roads	The machine moves only at a speed of 7 km/h. Device CAB does not recognize the 2nd gear.	Check the motion switch by Roads /cable connections, they are possible Changed.
E-170	KSR	The unloading Pipe Not Turns		The potentiometer is not controlled. The auger jumps, the pre-tension of the spring is too small, the wear of the toothed segment, there are no teeth, power supply of the electromagnetic valve, no pressure rises.
E-171	KSR	The difference of end stops of the unloading pipe position is too small
E-172	Autopath Cac	The difference of the end stop of the copier on the right is too small
E-173	Autopath Cac	The difference of the end stop of the copier on the left is too small
E-174	Autopath Cac	The difference of limit stops of the prefix height is too small
E-175	KSR	The difference of end stops of the unloading pipe height is too small
E-176	KSR	Damper limit stop difference is too small
E-179	Electro-hydraulic drive of chassis EFA	Faulty input/output of the switching facilitation device	Switching gears is difficult.	The valve of the switching relief device is not switched on. The malfunction can be eliminated only by replacing the module EFA.

Code	Module	Fault	Working State	Eliminating
E-180	Electro-hydraulic drive of chassis EFA	The permissible values of the movement lever potentiometer have not been reached	Only when examining the potentiometer of the movement lever: The study can not be successfully completed, because the collected values of the potentiometer do not lie in an acceptable range.	The movement potentiometer signal does not reach the following Values or exceeds Their: The lever of movement is completely ahead: 6.9-7.3 in Control lever in neutral position: 3.8-4.2 in Lever of movement completely behind: 0.8-1.2 in Check the control system of the movement potentiometer. Check Cable Connection.
E-182	Autopath Cac	Error Study End Stops
E-183	Autopath Cac	Error Study End Stops
E-185	ATP	Zero points Copying Auto pilot arcs ATP Not okay
E-186	ATP	Angle of the wheels outside the permitted tolerance field for direct movement
E-187	Device CAB	Switching to boosting gear is not possible
E-188	ATP	Not Connected Carbon copy System
E-189	KSR	The approach to all end stops has not been fulfilled
E-190	KSR	The difference between the left/right values is too small
E-191	KSR	Unloading pipe position outside of the learned end stops		The unloading tube for training does not move to the end stop.

Code	Module	Fault	Working State	Eliminating
E-192	GGS	Incorrect signals CAN, Start aborted
E-193	Electro-hydraulic drive of chassis EFA	No hydraulic pump speed sensor signal	Limited Operation: Movement to Max. 7 km/hour on the 1st transfer, Approx. 12 km/h on 2nd gear	No speed sensor signals: Check the cable connection of the module With The speed sensor on the Breakage.
			“Engine Not Turns”	Check the plug-in connection of the speed sensor.
				Replace Sensor Speed Rotation.
E-194	Electro-hydraulic drive of chassis EFA	No hydraulic motor speed sensor signal	Limited Operation: Movement to Max. 7 km/hour on the 1st transfer, Approx. 12 km/h on 2nd gear	No speed sensor signals: Check the cable connection of the module With The speed sensor on the Breakage.
				Check the plug-in connection of the speed sensor.
				Replace Sensor Speed Rotation.

Code	Module	Fault	Working State	Eliminating
E-195	Electro-hydraulic drive of chassis EFA	No high-pressure sensor signal forward	Limited Operation: Movement to Max. 7 km/hour on the 1st transfer, Approx. 12 km/h on 2nd gear	No pressure sensor signal: Check the cable connection from the module to the pressure sensor on the breakage or short circuit.
				Check the plug-in connection of the speed sensor.
				Replace Sensor Pressure.
				Check the 14317.2 cable in the rear area to the pressure sensors in the shaft tube for damage.
E-196	Electro-hydraulic drive of chassis EFA	No high-pressure sensor signal back	Limited Operation: Movement to Max. 7 km/hour on the 1st transfer, Approx. 12 km/h on 2nd gear	No pressure sensor signal: Check the cable connection from the module to the pressure sensor on the breakage or short circuit.
				Check the plug-in connection of the speed sensor.
				Replace Sensor Pressure.
				Check the 14317.2 cable in the rear area to the pressure sensors in the shaft tube for damage.

Code	Module	Fault	Working State	Eliminating
E-197	Electro-hydraulic drive of chassis EFA	Switch Braking More Activated	The machine cannot be moved, although the movement lever is removed.	The malfunction is shown if the driver at the hill pushes the brake pedals with the foot and creates a brake pressure > 25 At least. If Fault Remains:
				Check the brake pressure switch under the driver’s Landing.
				Check the pedal switch under the driver’s Landing.
E-198	Fem	Missing Signal Spinner Performance
E-199	Electro-hydraulic drive of chassis EFA	The motion lock switch is not recognized	Machine Not Moves.	Check the system of levers, fastening, adjustment. Check the switching signal of the delock switch.
				Check the position of the control Roller/Control tab (on the potentiometer) relative to the segment.
				The deformation of the reed is possible. Neutral position = 3.8-3.9 in on display
E-200	ESR	The speed sensors are not recognized Mowing Devices
E-201	ESR	The left speed sensor is not connected Mowing Apparatus

Code	Module	Fault	Working State	Eliminating
E-202	ESR	Medium speed sensor not connected Mowing Apparatus
E-203	ESR	The speed sensor is not connected to the right Mowing Apparatus
E-204	ESR Hydra.	Console More Revolves
E-205	ESR Hydra.	Pressure sensor for hydraulic feeding device faulty
E-206	ESR	The speed of the prefix is not recognized
E-211	Device CAB	Module output CAB, output 2, disconnected due to excess temperature
E-212	Device CAB	Module output CAB, output 3, disconnected due to excess temperature
E-213	Device CAB	Module output CAB, output 15, disconnected due to excess temperature
E-214	Device CAB	Module output CAB, output 16, disabled due to excess temperature
E-215	Device CAB	Module output CAB, output 29, disabled due to excess temperature
E-216	Device CAB	Module output CAB, output 30, disconnected due to excess temperature